notesalad2

How to Replace a Kia Sportage Replacement Key The key of many Kia models comes with an electronic keyless entry system built in. The key can be compared to an remote control, and is able to be replaced with a new one from a Kia dealer or a locksmith. Key fobs may stop working due to a variety of reasons, including an inactive battery, worn out buttons signal interference, or water damage. Here are some suggestions on how you can get your Kia Sportage replacement key working again. How do you replace the remote key or smartkey No matter if your Kia is equipped with an intelligent key, remote key push-to-start key, or a regular non-transponder metal key The battery inside these keys will eventually require replacement. This is particularly relevant if your vehicle displays a message indicating that the smart or remote keys are in poor condition. Fortunately, it's an easy process. To replace the battery on the keyfob remove the mechanical key from the slot at the back of the fob. Then, push the cover open. A small screw will be in the key fob to keep the battery in place. Remove the old battery by detaching the screw with a small screwdriver. Install the new battery and then close the slit on the key fob. Test the key fob by pressing the lock and unlock buttons. It's okay in case the doors lock and unlock as you expect. You can now use the hands-free feature to lock and unlock your Kia when your fingers get cold or when you need to run errands around Brandon. Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a specific programming machine that only the dealer or automotive locksmith can access. Other keys (non transponder keys made of steel) do not require programming. If you're looking to reprogramme your key, you'll have to record the key code number on the key code tag. How do I replace the battery? If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a sign that the battery needs to be replaced. A low battery may cause other issues, like the check engine light flashing or the engine not running correctly. It is fairly easy to replace key fob batteries using just two tools. Before beginning the process ensure that your vehicle is turned off and that all doors are closed. Find the small, metal or plastic piece on the bottom of the key fob. Then, kia picanto key fob replacement until the key pops out. You can then insert the key into the driver's door handle to unlock your car. To replace the key fob battery, take off the cover from the back and use a plier bar tool to loosen the latch that holds the black negative battery cable. Take the old battery out, and then position the new battery so that its “+” side faces you and the “–” negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or bending the metal contacts. Once the new battery has been installed then turn the key fob off and then on in the ignition several times until the door locks cycle. Then, test your Kia key fob to see if it is working properly again. How do you replace a keyless keys Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The difference between them is that the smart fob has a small mechanical key blade hidden within it, whereas the standard fob isn't equipped with. Both types of key fobs have batteries inside that will eventually have to be replaced. Fortunately, it's a fairly simple process that only takes about two minutes. Before you start it is important to ensure that you're on a flat surface with good lighting and that the Kia is off. Keep in mind that the fob is made up of small parts that can fall should you not be careful. The first step is to locate the small release button that is located on the back of the lower part of the fob. It's either an oval or circular slot. When you press it button, the mechanical blade will be released and you will be able to open the key fob. After the key fob has been opened, remove the battery that was in it. The new battery is a the CR-2032, and it can be bought on the internet or at your local auto parts store. Once you're done with the battery, you should be able to lock or unlock your car using your key fob, even if the engine isn't running! How do I replace the mechanical key The Kia keyfob is an excellent convenience, allowing us to lock or unlock our car with just pressing a button. Like any other device it will encounter issues at times. There are solutions to address these issues and keep your key fobs in good working order for an extended period of time. One of the most frequent problems is a low or dead battery. This can cause your fob to stop working or work intermittently. If this is the case then try replacing the battery with a new one. If this doesn't resolve the problem then try using a normal flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not to harm any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a new one. Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob and verify that it's working correctly. If the device isn't working, call an expert locksmith or dealer to solve the problem. To avoid locking outs in the future, ensure you have an emergency key that will work in all of the door and trunk cylinders.